Southern Utah Roofing SupplyVisit southernutahroofingsupply.com →

What Underlayment Should Go Under a Metal Roof?

2026-11-03 · James Willis

A metal roof needs a synthetic or high-temperature underlayment rated for sustained heat, not standard felt. In Cedar City and across Southern Utah, where summer roof surface temperatures run high and sun exposure is constant, the underlayment has to resist heat breakdown over years, not just shed water during installation.

Why Does Underlayment Matter More on a Metal Roof?

Metal panels transfer heat differently than asphalt shingles. Standard asphalt-saturated felt can soften, blister, or stick to the back of metal panels when temperatures climb, especially on south- and west-facing slopes common on Southern Utah homes. The underlayment sits between the panels and the deck as the actual water barrier, since metal seams and fastener penetrations rely on it as backup. Get this layer wrong and the symptoms (panel telegraphing, condensation staining, deck rot) show up years after installation, when they're expensive to trace back to the cause.

What Types of Underlayment Work Under Metal?

Three categories cover most Southern Utah metal roofing jobs:

Underlayment TypeHeat ToleranceTypical Use
High-temp syntheticHighest, built for direct metal contactStanding seam, exposed-fastener panels, full sun exposure
Standard synthetic (non-high-temp)ModerateLower-slope sections, shaded areas, secondary layers
Self-adhered (peel-and-stick) membraneHigh, plus seals around fastenersValleys, eaves, penetrations, ice-prone roof edges
30 lb. asphalt feltLow, not rated for sustained metal heatNot recommended as the primary layer under metal

Most metal roofing installs in this area pair a high-temp synthetic as the field underlayment with self-adhered membrane at vulnerable spots like valleys, pipe boots, and roof-to-wall transitions. The combination handles both the heat load from the panels above and the water concentration points below.

Does the Roof Pitch or Panel Type Change the Underlayment?

Yes. Standing seam panels, which clip to the deck with concealed fasteners, generally call for high-temp synthetic across the whole field because the panel sits tight against the underlayment with no air gap. Exposed-fastener panel systems puncture through at every screw line, so self-adhered membrane around those fastener rows adds a second seal the synthetic alone doesn't provide. Lower-slope sections of a roof, where water sits longer before draining, are also where a self-adhered membrane earns its place even if the rest of the roof uses standard synthetic.

What Happens If the Wrong Underlayment Goes Under Metal?

Using felt or a non-rated synthetic under metal panels typically shows up as softened or degraded underlayment within a few years rather than immediately, since the damage is heat-driven and cumulative. Once that layer fails, the roof deck has no real backup if a seam leaks or a fastener works loose, which turns a minor repair into a deck replacement. Matching the underlayment spec to the panel type at the start avoids that outcome entirely.

How Do I Know Which Underlayment My Project Needs?

The right choice depends on the panel system, roof pitch, slope orientation, and how much of the roof carries direct sun. Rather than guessing from a generic spec sheet, bring your project details to Southern Utah Roofing Supply and we'll match the underlayment to the panels you're ordering. See our current metal roofing material for panel options, or check pricing for underlayment and accessory availability. If you're still deciding between panel systems, our breakdown of metal roofing vs. asphalt shingles covers how the two compare before you get to underlayment specs. For a rundown of everything else a metal roof needs beyond the panels, see underlayment, flashing, and fasteners contractors forget to order.

We serve contractors and homeowners across Cedar City and Southern Utah, and our Covered with Care program is built around getting the right material matched to the right job before it ships.

FAQ

Can I use the same underlayment under metal that I'd use under shingles? No. Standard felt isn't rated for the sustained heat metal panels hold against the deck. Metal roofing calls for high-temp synthetic or self-adhered membrane instead.

Do I need self-adhered membrane across the whole roof, or just certain spots? Most jobs only need it at valleys, eaves, and penetrations, with synthetic underlayment covering the rest of the field. A full self-adhered layer is usually reserved for low-slope sections.

Does underlayment choice affect how long the roof lasts? It can. A mismatched underlayment degrades under heat well before the metal panels themselves show wear, so the underlayment often becomes the limiting factor on roof life, not the panel material.

← All posts